Peel and Stick Anti Slip Stair Tape 35ft Roll with Roller for Extra Grip
Peel and Stick Anti Slip Stair Tape 35ft Roll with Roller for Extra Grip
BUNDLE & SAVE
Couldn't load pickup availability
-
Ordered
- - -
Order Ready
- - -
Delivered
Peel and Stick Anti Slip Stair Tape 35ft Roll with Roller for Extra Grip
✦
A Smarter Step Toward Better Traction
Add Grip Where You Step.
Give suitable steps and walking surfaces a textured contact area with easy-to-cut anti-slip grip tape.
Designed with an 80-grit aluminum oxide surface, adhesive backing and a convenient cut-to-fit roll, this tape lets you create defined grip areas around your home, entrance and other suitable spaces.
▥
Textured Contact
Coarse surface designed to add traction where footwear meets the step.
✂
Cut to Fit
Measure your space and trim individual strips to suit your layout.
↔
Roller Included
Press the tape down evenly during application with the included roller.

A Practical Surface Upgrade
From Bare Steps to Added Traction.
Create defined grip areas without covering the entire staircase.
The black strips create a clear visual contrast against many lighter wood, tile and stone finishes. Cut consistent lengths for a coordinated layout, then position them on suitable flat tread surfaces.
01. Defined Grip Areas
Add textured contact areas where shoes land on suitable steps.
02. Flexible Placement
Plan strip lengths around the shape and usable space of each tread.
03. A Coordinated Finish
Keep spacing and alignment consistent across your steps.
Designed around your space: Cut individual strips to create a layout that suits your project.

Look Closer at the Contact Surface
Texture You Can See. Grip You Can Feel.
The difference starts with its coarse 80-grit surface.
Made with an 80-grit aluminum oxide finish, the granular texture is designed to increase traction at the contact area between footwear and a suitable walking surface.
80-Grit Aluminum Oxide
An abrasive surface provides the visible texture that distinguishes grip tape from a smooth tread.
Footwear Contact Area
Plan the layout so the strips sit within the flat areas used by shoes when stepping.
Adhesive Backing
Peel away the release liner and apply to a properly prepared, compatible surface. Firm pressure helps establish contact.
Built for traction, not cushioning. This is a coarse grip tape rather than a soft mat or cushioned barefoot tread.

A Careful Start Makes the Difference
Prepare. Cut. Press.
A straightforward application process with the included roller.
Take time to prepare the surface and plan your layout. Clean preparation and even pressure help the adhesive backing make proper contact.
Prepare the Surface
Remove dirt, oil and loose material. Make sure the compatible surface is sound, smooth, flat and fully dry before applying.
Measure, Cut & Apply
Measure the required length, cut the strip, peel the release liner and position it carefully. Keep the tape supported by the flat surface.
Press Firmly
Use the included roller to press the tape down evenly, paying attention to the edges. Follow the supplied installation instructions.
Important: Wait 1 hour after application before water exposure, according to the product guidance.
Do not bridge gaps, joints or unsupported edges. Follow any additional instructions supplied with the product.

For Suitable Indoor & Outdoor Locations
Ready for Everyday Exposure.
Add textured contact areas to suitable walking surfaces around your home.
The tape is specified to resist water, wear, oil and detergents. Choose placement carefully and keep installed strips clean and in good condition.
💧
Water Resistance
Observe the required waiting period before water exposure.
◈
Wear Resistance
Inspect regularly for worn areas, lifting edges or damage.
✓
Easy Maintenance
Remove oil, debris and residues to keep the walking area clear.
Keep the surface clear: Remove standing water, snow, ice, oil and debris. Replace loose or damaged strips.

Choose a Compatible Foundation
Check the Surface. Then Apply.
The condition of the surface matters just as much as the material itself.
The tape is intended for a range of suitable smooth, flat surfaces. Always check the condition and finish before applying.
Start with a Sound Surface
Avoid loose coatings, crumbling material, pronounced texture and uneven areas that prevent full adhesive contact.
Clean & Dry Thoroughly
Dirt, moisture and oil can interfere with adhesion. Prepare the area before removing the liner.
Test Before Completing the Layout
Check a small area for adhesion and finish compatibility. Follow the product guidance for your particular surface.
Surface names are not a guarantee of compatibility. Finishes, coatings, porosity and condition can affect adhesion.

Measure Your Project Before You Start
One Roll. Cut for Your Steps.
A continuous 35-foot roll gives you the flexibility to cut individual strips for your layout.
Keep the 4-inch width and trim the length to match the usable space on each compatible tread. Plan your cuts first to make the most of the roll.
Roll Length |
35 ft / approximately 10.67 m |
|---|---|
Tape Width |
4 in / approximately 10.16 cm |
Surface |
80-grit aluminum oxide |
Color |
Black |
Application |
Adhesive backing with peel-away release liner |
Package Includes |
1 grip tape roll + 1 application roller |
Cutting Example |
Up to 15 strips measuring 28 in / approximately 71.1 cm each |
Plan your coverage: 35 ft equals 420 inches. Dividing the roll into 28-inch lengths gives a theoretical maximum of 15 strips before trimming loss.
*Actual strip count depends on cut lengths, edge trimming and waste. Measuring tools, scissors, footwear and scene props are not included.

✦ ✧ A Practical Upgrade for Your Space
Measure Your Steps. Plan Your Grip.
Add textured contact areas to compatible surfaces with a cut-to-fit roll and an included application roller.
Prepare carefully, press firmly and maintain the installed strips for everyday use.
